Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
The article author is making a few good pointers related to Installing A Bathtub as a whole in this great article just below.
Mounting a bath tub isn't specifically rocket science, but it does require solid plumbing, woodworking, and sometimes, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably tough task. If the old bathtub is conveniently available, the job can relocate easily; if you have to open a wall to eliminate the old tub and also position the new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will need a helper to move out the old bathtub and also set in the brand-new one. See to it you have certified yourself for the work and also are comfortable attempting it. Rather than employing a service provider to take over a halfway-completed job, it is better to think about employing one before you begin. Possibilities are you might need a specialist plumber to make tube links.
This post will certainly aid you install a brand-new bathtub in your bathroom if you have already acquired a new tub and do not need to alter the setup of your previous supply of water pipelines.
Your tools as well as product list ought to consist of the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the limited access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a cloth ready for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washers remain in location in between the tap and also the sink. Safeguard the faucet in position with the manufacturer supplied backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The former type ought to be connected to the faucet ends first, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bath tub
Making use of both wooden boards under its feet, position the bathtub in the required setting. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the bathtub up until the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap connector to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
Switch on the water and also examine all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub and also check the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bath paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait till the bath tub has actually been used a minimum of when as this will certainly resolve it right into its last placement.
Getting ready for the Installment
Firstly, the supporting frame provided with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its final setting.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes as well as cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill the tub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealer can split relatively very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly available on the market. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that page on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while browsing on the web. Loved our entry? Please share it. Help someone else discover it. Thank you for your time. Please pay a visit to our site back soon.
Plumber on standby. Call! Report this page